R&D design and testing capabilities
National industry standard drafting unit for plate heat exchangers, plate heat exchanger units, absorption heat exchangers, and brazed plate heat exchangers. Member unit of National Boiler and Pressure Vessel Standardization Technical Committee. After years of development, THT Juyuan has accumulated rich experience in research and development, solutions, manufacturing, technology, energy conservation, services, etc., and has realized the transformation and upgrading from single equipment manufacturing to system integration, and from
Application in heating domestic water
Air compressor waste heat recovery It mainly recovers the heat generated by the compressed air of the air compressor. The oil circuit of the air compressor is cooled by cold water to produce hot water for domestic use. According to engineering experience, the heat that can be recovered by the lubricating oil circuit system accounts for about 60% of the waste heat. This part of the heat can be used for daily bathing, heating and constant temperature, and low-temperature process heating. Our company operates heat exchanger products: plate heat exchanger, H
Introduction to brazed plate heat exchanger
Brazing refers to a welding method in which the filler metal lower than the melting point of the weldment and the weldment are simultaneously heated to the melting temperature of the solder, and then the liquid filler metal is used to fill the gaps between the solid workpieces to connect the metals. Divided into hard soldering and soft soldering. Brazing is a brazing process where the melting point of the filler metal is higher than 450°C. Brazing materials include copper-based, silver-based, aluminum-based alloys. Commonly used fluxes include sand, boric acid,
R&D design and testing capabilities
plate heat exchanger has created many industry bests There are more than 120 plate types (10 semi-welded types) Maximum single plate heat exchange area: 4.0㎡ Maximum single machine installed area for engineering applications: 4000㎡ Maximum water treatment capacity of a single machine: 4500m3/h Maximum design pressure: 4.2MPa Maximum test pressure 5.5MPa For the first time in the industry, the long-term operation application of the removable gasket plate heat exchanger wi
R&D design and testing capabilities
Heat exchange and its system are important energy-saving equipment. Each plate replacement model of THT Juyuan is strictly tested by the National Heat Exchange Product Quality Supervision and Inspection Center (referred to as the National Inspection Center), and a performance test report is issued. The selection software is certified and registered by AHRI and undergoes compliance verification every year, ensuring the accuracy of plate heat exchanger selection calculation
Application of brazed plate heat exchanger
The selection design uses special software to perform data iteration calculations to complete the thermal and hydraulic calculations of the heat exchanger, including inter-plate flow velocity, corner hole flow velocity, resistance drop, thermal mixing design, heat transfer coefficient, logarithmic average temperature difference and heat transfer area, etc., and can calculate the resistance drop at the corner holes and the resistance drop between the flow channels respectively as required, and can make corresponding economic analysis on the selected model of the heat exchanger.
System product technology-multi-effect evaporation system
In multi-effect evaporation, heating steam is added to the first effect. The secondary steam generated from the first effect is used as the heating steam for the second effect. The heating chamber of the second effect is equivalent to the condenser of the first effect. The secondary steam generated from the second effect is used as the heating steam for the second effect. The secondary steam is used as the third effect heating steam. Multiple evaporators are connected in series to form multi-effect evaporation. Since the operating pressure of the evaporation chamber is reduced effect by effect
Functional test: 8 sets of hydraulic test equipment, 1 set of vacuum pump set, 1 set of helium mass spectrometer leak detector, 1 set of drying equipment, 1 set of integrated heat exchange device debugging system and hydraulic test system, 1 full flow experimental bench Set, pilot test center (including fatigue test and thermal performance test of heat exchanger); Important equipment: 50,000-ton press, 40,000-ton press, 22,000-ton press, 16,000-ton press, 6,000-ton press plate automatic production line, 630-ton overall blanking
Product manufacturing and inspection capabilities
Plate high-precision pressing unit Thin plate precision blanking unit - first pressing and then punching process to ensure the roundness of the corner holes. It has the largest tabletop punching machine in the industry with a capacity of 630 tons to complete the blanking of large plates in one go. Mold data processing center unit
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
